Belkin F5D52314 - Cable/DSL Gateway Router Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Sítě Belkin F5D52314 - Cable/DSL Gateway Router. User manual for LANCNC-FAD Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 22
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
LANCNC-FAD
FTP Server for Fadal CNC Controls
2008-2009 Calmotion LLC, All rights reserved
Calmotion LLC
9909 Topanga Canyon Blvd. #322
Chatsworth, CA 91311
www.calmotion.com
- 1 -
2008-2009 Calmotion LLC, All rights reserved
Zobrazit stránku 0
1 2 3 4 5 6 ... 21 22

Shrnutí obsahu

Strany 1 - LANCNC-FAD

LANCNC-FADFTP Server for Fadal CNC Controls2008-2009 Calmotion LLC, All rights reservedCalmotion LLC9909 Topanga Canyon Blvd. #322Chatsworth, CA 9131

Strany 2

Deciding on a network configurationThere are several ways to design a network. Some knowledge and experience with setting up networks is highly sugges

Strany 3

Figure 32. Select “Network Connections” and the following screen should appear.Figure 43. Highlight the “Local Area Connection” and right click the mo

Strany 4

Figure 54. Select “Internet Protocol (TCP/IP)” so that it is highlighted and click the “Properties” button. A new screen will pop up. Select the butto

Strany 5

Figure 65. You may exit from the Control Panel. Start Internet Explorer and type ftp://192.168.2.111 in the address bar. A screen similar to the one s

Strany 6

Figure 7Follow the instructions that come up in Internet Explorer to view the files in an ftp viewer window. (Click “Page”, and then click “Open FTP S

Strany 7

Figure 8The figure above shows the display on a PC when the ftp site has been opened from the previous step. At this screen, files can transferred fr

Strany 8

Example 2, Wired Network connection to the LANCNC-FAD using a routerThe diagram below shows a wired network configuration using a network router. The

Strany 9 - Command: VW,FILENAME+

The following is an example of what a network router LAN configuration page should look like. You typically access the LAN settings via a web browser

Strany 10

Example 3, Wireless Network connection to the LANCNC-FAD using a router and a Wireless BridgeThe diagram below shows a Wireless Network connection to

Strany 11 - Figure 4

Use the following step-by-step procedure to setup the router and then the access point. These settings are based on using a Belkin Wireless G router a

Strany 12 - Figure 5

IntroductionThis manual is intended to provide a description of the Calmotion LANCNC-FAD FTP file server for Fadal CNC’s. Some knowledge of LAN is req

Strany 13 - Figure 6

Changing the baud rate on the LANCNC-FAD deviceThe LANCNC-FAD defaults to 38,400 baud. If a different baud rate is desired, verify that the CNC can s

Strany 14 - Figure 7

capability, use the MU command at the ENTER NEXT COMMAND prompt and go to page for Change Device.5. Verify the LANCNC-FAD device matches the baud rate

Strany 15 - Figure 8

Revision History:Rev 2.4 Initial releaseRev 2.51. Added INI+ and the RESET+ commandsRev 2.91. Added retry on FTP transfersRev 3.01. DNC repeats same

Strany 16

Description of OperationThe LANCNC-FAD acts as an FTP server for file storage that in turn can be accessed by a Fadal CNC. Connection to the FTP serve

Strany 17 - Figure 9

List of Available CommandsLANCNC-FAD plus CommandDescriptionDE,FILENAME+ Delete the FILENAMEDNC,FILENAME+ DNC the FILENAME (Use DNCX for X-modem)DNC,F

Strany 18

Command: PU,0,FILENAME+Description: Punch command. Saves program and tooling data to the SD card from the CNC memory. Refresh the computers FTP softw

Strany 19

Command: PU,3,FILENAME+Description: Punch command. This saves all programs in CNC to the SD card from the CNC memory. Refresh the computers FTP softwa

Strany 20

Command: DNC,FILENAME,?+Description: DNC, Direct Numerical Control with block search. The DNC command has an optional parameter to start at a specific

Strany 21

Command: HELP+Description: Display the commands available for use with the LANCNC-FAD device.Example:Command: INI+Description: Displays the current IP

Strany 22

Command: VW,FILENAME+Description: Displays the first 12 lines of the file specified. This can be used before loading or deleting files to verify the

Komentáře k této Příručce

Žádné komentáře